![]() The following example shows how to configure a static route tracker with TCP port endpoint:ĭevice(config-endpoint-tracker)# endpoint-ip 10.0.0.1ĭevice(config-endpoint-tracker)# interval 10ĭevice(config-endpoint-tracker)# multiplier 1ĭevice(config-track)# ip route vrf 1 192.168.0.0 255.255.0.0 10.1.19.16 100 track name tcp-10001 If endpoint-ip is not configured, the commit CLI fails. This is the destination on the internet to which the probes are sent to determine the status of No endpoint-ip ip-address Syntax Description ip-address To disable the configuration, use the no form of this command. To configure the IP address of an endpoint, use the endpoint-ip command in endpoint tracker configuration mode. The following example shows how to configure the DNS name:ĭevice(config-endpoint-tracker)# endpoint-dns-name The following example shows how to configure a DNS name for the NAT DIA interface:ĭevice(config-endpoint-tracker)# endpoint-dns-name Device(config-endpoint-tracker)# tracker-type interface endpoint-ip If endpoint-dns-name is not configured, tracker is disabled. This is the destination on the internet to which probes are sent to determine the status of theĭNS name can contain a minimum of 1 character and a maximum of 253 characters. No endpoint-dns-name dns-name Syntax Description dns-nameĭNS name of the endpoint. To configure the domain system name of an endpoint, use the endpoint-dns-name command in endpoint tracker configuration mode. The following example shows how to configure an API URL: Device(config)# endpoint-tracker tracker1ĭevice(config-endpoint-tracker)# endpoint-api-url endpoint-dns-name If endpoint-api-url is not configured, tracker is disabled. This is the destination in the internet to which the router sends probes to determine the status of No endpoint-api-url url-address Syntax Description url-addressĪPI URL of an endpoint. To diable API URL configuration, use the no form of this command. ![]() To configure the API URL of an endpoint, use the endpoint-api-url command in endpoint tracker configuration mode. The following example shows how to configure tracker groups using boolean logic to probe NAT DIA interface:ĭevice(config)# endpoint-tracker tracker1ĭevice(config-endpoint-tracker)# tracker-type interfaceĭevice(config)# endpoint-tracker tracker2ĭevice(config-endpoint-tracker)# endpoint-dns-name Device(config-endpoint-tracker)# threshold 1000ĭevice(config-endpoint-tracker)# interval 600ĭevice(config-endpoint-tracker)# tracker-elements tracker1 tracker2ĭevice(config-endpoint-tracker)# boolean orĭevice(config-endpoint-tracker)# exit endpoint-api-url The following example shows how to configure a tracker group with two static route trackers (two endpoints) using the trackerĭevice(config)# endpoint-tracker tcp-10001ĭevice(config-endpoint-tracker)# tracker-type static-routeĭevice(config-endpoint-tracker)# endpoint-ip 10.1.1.1ĭevice(config-endpoint-tracker)# threshold 100ĭevice(config-endpoint-tracker)# multiplier 10ĭevice(config-endpoint-tracker)# interval 1ĭevice(config)# track tcp-10001 endpoint-trackerĭevice(config)# endpoint-tracker udp-10002ĭevice(config-endpoint-tracker)# endpoint-ip 10.2.2.2ĭevice(config-endpoint-tracker)# multiplier 5ĭevice(config-endpoint-tracker)# interval 2ĭevice(config)# track udp-10002 endpoint-trackerĭevice(config)# endpoint-tracker static-route-groupĭevice(config-endpoint-tracker)# tracker-type tracker-groupĭevice(config-endpoint-tracker)# tracker-elements tcp-10001 udp-10002ĭevice(config-endpoint-tracker)# boolean andĭevice(config)# track static-route-group endpoint-tracker You can apply only one tracker to a static route endpoint. Similarly, to create a NAT Direct Internet Access (DIA) tracker group, you can combine an IPĪddress tracker and a DNS tracker. For example, to create a static route group, you can combine an IP address OR logic ensures that the endpoint status is reported as active if either one of the associated trackers of the tracker groupĪND logic ensures that the endpoint status is reported as active if both the associated trackers of the tracker group reportĮndpoint-tracker configuration (config-endpoint-tracker) Command History ReleaseĪ tracker group can have a mix of endpoint trackers. Specifies boolean AND or OR logic that is used to configure a tracker group. To disable boolean logic, use the no form of this command. ![]() To enable boolen logic while configuring a tracker group, use the boolean command in endpoint tracker configuration mode.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |